Design and Fabrication of Sambar Serving Machine
DOI:
https://doi.org/10.32628/IJSRMME24836Keywords:
Vending Machine, Sambar, Conceptual DesignAbstract
We know that are many ways to fabricate sambar vending machine, but all these ways take more time. Our aim is to reduce the time by “Design and Fabrication of Sambar Serving Machine” and increase the productivity. By this method pouring operations can be performed in a sequence. They are sambar, water, milk etc… by using clutch mechanism and lifter. This method reduces human effort and saves the production time. Apart from other methods this method can be used in places where investment cost has to be minimized. The device has been fabricated and tested which was able to perform the serving of sambar in in a controlled and consistent manner.
References
Kumaraswamy, J., Anil, K.C., Canbay, C.A., N D Shiva Kumar. Electro-Whirling Stir Casting: a Novel Approach for Fabricating Al7075/SiC MMCs with Enhanced Thermal Characteristics. Silicon (2023). https://doi.org/10.1007/s12633-023-02678-y DOI: https://doi.org/10.1007/s12633-023-02678-y
J. Kumaraswamy, Anil K C, T R Veena, G. Purushotham, Sunil Kumar K, “Investigating the Mechanical Properties of Al 7075 Alloy for Automotive Applications: Synthesis and Analysis” in Scopus indexed EVERGREEN Journal with ISSN: 2189-0420, Vol. 10, Issue 03, pp.1286-1295, September 2023. DOI: https://doi.org/10.5109/7151674
Kumaraswamy, J., Anil, K. C., Veena, T. R., Reddy, M., & Sunil Kumar, K. (2023). Influence of particulates on microstructure, Mechanical and Fractured behaviour on Al-7075 alloy composite by FEA. Australian Journal of Mechanical Engineering, 1–15. https://doi.org/10.1080/14484846.2023.2276987 DOI: https://doi.org/10.1080/14484846.2023.2276987
Sunil Kumar, K., Srinivasamurthy, P.L.”Tensile and Hardness Behavior of RRA Treated Aluminum 7075 Alloy”, Lecture Notes in Mechanical Engineering, 2021, 23, pp. 563–575 DOI: https://doi.org/10.1007/978-981-15-4739-3_49
Kumaraswamy Jayappa, Kyathasandra Chikkanna Anil, Zulfiqar A. Khan, Enhancing wear resistance in Al-7075 composites through conventional mixing and casting techniques, Journal of Materials Research and Technology, Volume 27, 2023, pp. 7935-7945. https://doi.org/10.1016/j.jmrt.2023.11.171. DOI: https://doi.org/10.1016/j.jmrt.2023.11.171
J. Kumaraswamy, V. Kumar and G. Purushotham, A review on mechanical and wear properties of ASTM a 494 M grade nickel-based alloy metal matrix composites, Materials Today: Proceedings, Vol 37, 2021, pp 2027–2032, https://doi.org/10.1016/j.matpr.2020.07.499. DOI: https://doi.org/10.1016/j.matpr.2020.07.499
Sunil Kumar, K., Srinivasa Murthy, P.L., “Retrogression and re-aging of AL-7075 microstructure and corrosion behavior characterization”, International Journal of Engineering and Advanced Technology, 2019, 9(1), pp. 4377–4383 DOI: https://doi.org/10.35940/ijeat.F8452.109119
K. Jayappa, V. Kumar, and G. G. Purushotham, “Effect of reinforcements on mechanical properties of nickel alloy hybrid metal matrix composites processed by sand mold technique,” Applied Science and Engineering Progress, Vol. 14, no. 1, pp. 44–51, Jan.–Mar. 2021. http://dx.doi.org/10.14416/j.asep.2020.11.001 DOI: https://doi.org/10.14416/j.asep.2020.11.001
J. Kumaraswamy, V. Kumar and G. Purushotham, Thermal analysis of nickel alloy/Al2O3/TiO2 hybrid metal matrix composite in automotive engine exhaust valve using FEA method, Journal of Thermal Engineering, Vol. 7, No. 3, March, 2021, pp. 415-428. https://dx.doi.org/10.18186/thermal.882965. DOI: https://doi.org/10.18186/thermal.882965
J Kumaraswamy, Vijaya Kumar, G Purushotham, Evaluation of the microstructure and thermal properties of (ASTM A 494 M grade) nickel alloy hybrid metal matrix composites processed by sand mold casting, International Journal of Ambient Energy, Vol. 43, pp. 4899–4908. https://www.tandfonline.com/doi/abs/10.1080/01430750.2021.1927836. DOI: https://doi.org/10.1080/01430750.2021.1927836
Sunil Kumar, K., Srinivasa Murthy, P.L., “Effect of retrogression and re-aging on fatigue crack growth behavior of Al 7075 Alloy”, International Journal of Innovative Technology and Exploring Engineering, 2019, 8(10), pp. 243–247 DOI: https://doi.org/10.35940/ijitee.I8010.0881019
Kumaraswamy J, Anil K. C., Vidyasagar Shetty and C Shashishekar. Wear behaviour of the Ni-Cu alloy hybrid composites processed by sand mold casting, Advances in Materials and Processing Technologies (Tylor and Francis), Vol. 2, pp. 1-17. https://doi.org/10.1080/2374068X.2022.2092684 DOI: https://doi.org/10.1080/2374068X.2022.2092684
J. Kumaraswamy et al., "Thermal Analysis of Ni-Cu Alloy Nanocomposites Processed by Sand Mold Casting," Advances in Materials Science and Engineering, vol. 2022, Article ID 2530707, 11 pages, 2022. https://doi.org/10.1155/2022/2530707. DOI: https://doi.org/10.1155/2022/2530707
J. Kumaraswamy, K.C. Anil and V. Shetty, Development of Ni-Cu based alloy hybrid composites through induction furnace casting, Materials Today: Proceedings. https://doi.org/10.1016/j.matpr.2022.09.215 DOI: https://doi.org/10.1016/j.matpr.2022.09.215
Sharan kumar, Akash, Anil K C, Kumaraswamy J, Solid Particle Erosion Performance of Multi-layered Carbide Coatings (WC-SiC-Cr3C2), EVERGREEN Joint Journal of Novel Carbon Resource Sciences & Green Asia Strategy, Vol. 10, Issue 02, pp 813-819, June 2023. https://doi.org/10.5109/6792833 DOI: https://doi.org/10.5109/6792833
Anil K C, Kumaraswamy J, Mahadeva Reddy, Mamatha K M, Air Jet Erosion studies on Aluminum - Red Mud Composites using Taguchi Design, EVERGREEN Joint Journal of Novel Carbon Resource Sciences & Green Asia Strategy, Vol. 10, Issue 01, pp130-138, March 2023. https://doi.org/10.5109/6781059. DOI: https://doi.org/10.5109/6781059
Sunil Kumar, K., Srinivasa Murthy, P.L., “Study on tribological characterization of RRA treated aluminium 7075 alloy”, Journal of Advanced Research in Dynamical and Control Systems, 2019, 11, pp. 560–569
Sandeep Khelge, Vijaya Kumar and Kumaraswamy J, Optimization of wear properties on aluminum alloy (LM22) hybrid composite, Materials Today: Proceedings, Vol. 52, Part 3, pp. 565--570, 2022. https://doi.org/10.1016/j.matpr.2021.09.518 DOI: https://doi.org/10.1016/j.matpr.2021.09.518
Vidyasagar Shetty, Shabari Shedthi B and Kumaraswamy J, Predicting the thermodynamic stability of perovskite oxides using multiple machine learning techniques, Materials Today: Proceedings, Vol. 52, Part 3, pp. 457-461, 2022. https://doi.org/10.1016/j.matpr.2021.09.208 DOI: https://doi.org/10.1016/j.matpr.2021.09.208
Harish R S, Sreenivasa Reddy M, Kumaraswamy J, Wear characterization of Al7075 Alloy hybrid composites, Journal of Metallurgical and Materials Engineering, Vol. 28 (2), pp. 291-303. https://doi.org/10.30544/821. DOI: https://doi.org/10.30544/821
K.C. Anil, J. Kumaraswamy, Akash et al., Experimental arrangement for estimation of metal-mold boundary heat flux during gravity chill casting, Materials Today: Proceedings. https://doi.org/10.1016/j.matpr.2022.07.399 DOI: https://doi.org/10.1016/j.matpr.2022.07.399
R.S. Harish, M. Sreenivasa Reddy and J. Kumaraswamy, Mechanical behaviour of Al7075 alloy Al2O3/E-Glass hybrid composites for automobile applications, Materials Today: Proceedings. https://doi.org/10.1016/j.matpr.2022.08.460 DOI: https://doi.org/10.1016/j.matpr.2022.08.460
Anil, K.C., Kumarswamy, J., Reddy, M., Prakash, B., Mechanical Behaviour and Fractured Surface Analysis of Bauxite Residue & Graphite Reinforced Aluminium Hybrid Composites, Frattura ed Integrità Strutturale, 16 (62) (2022) 168-179. DOI: 10.3221/IGF-ESIS.62.12 DOI: https://doi.org/10.3221/IGF-ESIS.62.12
Sandeep Khelge, Vijaya Kumar, Vidyasagar Shetty and Kumaraswamy J, Effect of reinforcement particles on the mechanical and wear properties of aluminium alloy composites: Review, Materials Today: Proceedings, Vol. 52, Part 3, pp. 571-576, 2022. https://doi.org/10.1016/j.matpr.2021.09.525 DOI: https://doi.org/10.1016/j.matpr.2021.09.525
Anil Kyathasandra Chikkanna, Kuchangi Venkatappa Manjunath, Kumaraswamy Jayappa, Mahadeva Reddy, Akash Biradar, Effect of Chilling & B4C content on Machining Efficiency and Surface Quality in Wire-Cut Machining of Aluminum Matrix Chilled Composites, Mechanics of Advanced Composite Structures, Volume 11, Issue 2 Pages 341-350. https://doi.org/10.22075/macs.2024.31090.1528
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Nikhil T, Lokesh Yadhav B R, Madan T L, Manjunath P, Manu S (Author)
This work is licensed under a Creative Commons Attribution 4.0 International License.
