Designed and Analysed of Three Distinct Composite Material-Based Mano Leaf Spring using ANSYS
DOI:
https://doi.org/10.32628/IJSRMME24822Keywords:
Composite Material, Leaf Spring, ANSYS Software, Carbon Material, Glass MaterialAbstract
The leaf spring is an important component in vehicles because it provides a comfortable ride and stability to the vehicle. The need to replace leaf springs with stronger and more lasting leaf springs is a key challenge in the transportation and automotive industries. In addition to offering ride comfort and stability, traditional steel leaf springs have a significant impact on the weight of the car. Fibre reinforced polymeric composites, therefore, are appropriate materials for various applications due to their many exceptional properties, including high wear resistance, high strength, long fatigue life, corrosion resistance, and low density. Fiber-reinforced polymeric composites find extensive application in several technical sectors, such as automotive, aviation, military, and marine industries. The utilization of composite materials has become imperative in the automotive industry to attain weight reduction without compromising material strength, as fuel consumption and CO2 emissions have to be reduced. In this paper, three different types of composite-based mono leaf springs were designed and examined. The results of the investigations showed that the 0° unidirectional glass fiber system was unable to correctly produce the required spring rate. Consequently, many combinations of carbon and glass hybrid systems were studied. The analysis showed that the desired spring rate was produced by the material configuration of [0°6G / 0°2C / 0°22G] S. When the final results were contrasted with the FEA findings, it was found that they concurred.
References
M. M. Shokrieh and D. Rezaei, “Analysis and optimization of a composite leaf spring,” Compos. Struct., vol. 60, no. 3, pp. 317–325, 2003, doi: 10.1016/S0263-8223(02)00349-5. DOI: https://doi.org/10.1016/S0263-8223(02)00349-5
B. B. Deshmukh and S. B. Jaju, “Design and analysis of glass fiber reinforced polymer (GFRP) leaf spring,” Int. Conf. Emerg. Trends Eng. Technol. ICETET, pp. 82–87, 2011, doi: 10.1109/ICETET.2011.61. DOI: https://doi.org/10.1109/ICETET.2011.61
S. Seralathan et al., “Finite element analysis of hybrid composite material based leaf spring at various load conditions,” Mater. Today Proc., vol. 33, no. xxxx, pp. 3540–3548, 2020, doi: 10.1016/j.matpr.2020.05.456. DOI: https://doi.org/10.1016/j.matpr.2020.05.456
G. Shankar and S. Vijayarangan, “Mono Composite Leaf Spring for Light Weight Vehicle–Design, End Joint Analysis and Testing,” Mater. Sci., vol. 12, no. 3, pp. 220–225, 2006.
E. Mahdi, O. M. S. Alkoles, A. M. S. Hamouda, B. B. Sahari, R. Yonus, and G. Goudah, “Light composite elliptic springs for vehicle suspension,” Compos. Struct., vol. 75, no. 1–4, pp. 24–28, 2006, doi: 10.1016/j.compstruct.2006.04.082. DOI: https://doi.org/10.1016/j.compstruct.2006.04.082
H. A. Al-Qureshi, “Automobile leaf springs from composite materials,” J. Mater. Process. Technol., vol. 118, no. 1–3, pp. 58–61, 2001, doi: 10.1016/S0924-0136(01)00863-9. DOI: https://doi.org/10.1016/S0924-0136(01)00863-9
G. Joshua Jacob and M. Assistant professor, “Design And Analysis Of Leaf Spring In A Heavy Truck,” Ijitr) Int. J. Innov. Technol. Res., no. 5, pp. 7041–7046, 2017, [Online]. Available: http://www.ijitr.com.
K. Krishnamurthy, P. Ravichandran, A. Shahid Naufal, R. Pradeep, and K. M. Sai HarishAdithiya, “Modeling and structural analysis of leaf spring using composite materials,” Mater. Today Proc., vol. 33, no. xxxx, pp. 4228–4232, 2020, doi: 10.1016/j.matpr.2020.07.346. DOI: https://doi.org/10.1016/j.matpr.2020.07.346
P. K. Mallick, Fiber-reinforced Composites: Materials, Manufacturing, and Design, Third Edit. Taylor & Francis Group, 2007. DOI: https://doi.org/10.1201/9781420005981
N. V. R. Reddy, K. S. Reddy, A. C. Basha, and B. RajNaveen, “Design and analysis of composite leaf spring for military jeep,” Int. J. Mech. Eng. Technol., vol. 8, no. 4, pp. 47–58, 2017.
Z. Yinhuan, X. Ka, and H. Zhigao, “Finite element analysis of composite leaf spring,” ICCSE 2011 - 6th Int. Conf. Comput. Sci. Educ. Final Progr. Proc., no. Iccse, pp. 316–319, 2011, doi: 10.1109/ICCSE.2011.6028643. DOI: https://doi.org/10.1109/ICCSE.2011.6028643
A. Swain and T. Roy, “Viscoelastic modelling and dynamic characteristics of CNTs-CFRP-2DWF composite shell structures,” Compos. Part B Eng., vol. 141, no. December 2017, pp. 100–122, 2018, doi: 10.1016/j.compositesb.2017.12.033. DOI: https://doi.org/10.1016/j.compositesb.2017.12.033
C. Llopis-Albert, F. Rubio, and S. Zeng, “Multiobjective optimization framework for designing a vehicle suspension system. A comparison of optimization algorithms,” Adv. Eng. Softw., vol. 176, no. November 2022, p. 103375, 2023, doi: 10.1016/j.advengsoft.2022.103375. DOI: https://doi.org/10.1016/j.advengsoft.2022.103375
S. Gunes, E. Manay, E. Senyigit, and V. Ozceyhan, “A Taguchi approach for optimization of design parameters in a tube with coiled wire inserts,” Appl. Therm. Eng., vol. 31, no. 14–15, pp. 2568–2577, 2011, doi: 10.1016/j.applthermaleng.2011.04.022. DOI: https://doi.org/10.1016/j.applthermaleng.2011.04.022
D. Samborsky, J. Mandell, and P. Agastra, “3-D Static Elastic Constants and Strength Properties of a Glass/Epoxy Unidirectional Laminate,” Bozeman Mont. State Univ., 2012, [Online]. Available: http://www.coe.montana.edu/composites/documents/3D Static Property Report.pdf.
