Design and Development of Solar Powered Water Purifier
DOI:
Keywords:
Research Paper, Solar energy, sustainableAbstract
A solar-powered water purifier is an innovative solution that utilizes solar energy to provide clean drinking water. This system harnesses the sun's power to drive purification processes such as filtration, distillation, or ultraviolet (UV) sterilization, eliminating contaminants like bacteria, viruses, and chemicals. It is energy-efficient, eco-friendly, and ideal for remote or off-grid areas where access to electricity is limited. By combining renewable energy with water purification technology, solar-powered purifiers offer a sustainable way to improve water quality while reducing reliance on traditional power sources.
References
Bharath, L., Kumaraswamy, J., Manjunath, T.V. et al. (2024). Evaluation of microstructure and prediction of hardness of Al–Cu based composites by using artificial neural network and linear regression through machine learning technique. Multiscale and Multidiscipline Modeling, Experiments, and Design. Springer. https://doi.org/10.1007/s41939-024-00525-0
Kyathasandra Chikkanna, A., Manjunath, K. V., Jayappa, Kumaraswamy, Mahadeva Reddy, and Akash Biradar. (2024). Effect of chilling & B4C content on machining efficiency and surface quality in wire-cut machining of aluminum matrix chilled composites. Mechanics of Advanced Composite Structures, 11, 341–350. Semnan University Press.
Kumaraswamy, J., Anil, K. C., Vidyasagar Shetty, and Shashishekar, C. (2023). Wear behaviour of the Ni-cu alloy hybrid composites processed by sand mould casting. Advances in Materials and Processing Technologies, 9, 351–367. Taylor & Francis.
Kumaraswamy, J., Anil, K. C., and Khan, Z. A. (2023). Enhancing wear resistance in Al 7075 composites through conventional mixing and casting techniques. Journal of Materials Research and Technology, 27, 7935–7945. Elsevier.
Kumaraswamy, J., Anil, K. C., Veena, T. R., Purushotham, G., and Sunil Kumar. (2023). Investigating the mechanical properties of al 7075 alloy for automotive applications: Synthesis and analysis. Transdisciplinary Research and Education Center for Green Technologies, Kyushu University.
Kumaraswamy, J., Anil, K. C., and Mahadeva Reddy. (2023). Influence of particulates on microstructure, mechanical and fractured behaviour on Al-7075 alloy composite by FEA. Australian Journal of Mechanical Engineering. Taylor & Francis.
Sharan Kumar, Anil, K. C., and Kumaraswamy, J. (2023). Solid particle erosion performance of multi-layered carbide coatings. Transdisciplinary Research and Education Center for Green Technologies, Kyushu University.
Anil, K. C., Kumaraswamy, J., Mahadeva Reddy, and Mamatha, K. M. (2023). Air jet erosion studies on aluminum-red mud composites using taguchi design. Transdisciplinary Research and Education Center for Green Technologies, Kyushu University.
Kumaraswamy, J., Vidyasagar Shetty, S., Sanman, S., Naik, P., Shedthi, S., Gnanavel, C., and Mogose, I. N. (2022). Thermal analysis of ni-cu alloy nanocomposites processed by sand mold casting. Advances in Materials Science and Engineering. Hindawi.
Kumaraswamy, J., Kumar, V., and Purushotham, G. (2022). Evaluation of the microstructure and thermal properties of (ASTM a 494 m grade) nickel alloy hybrid metal matrix composites processed by sand mold casting. International Journal of Ambient Energy, 43, 4899–4908. Taylor & Francis.
Hashim, J., Looney, L., & Hashmi, M. S. J. (2002). Particle distribution in cast metal matrix composites-Part II. Journal of Materials Processing Technology, 123, 258-263. https://doi.org/10.1016/S0924-0136(02)00099-7
Naher, S., Brabazon, D., & Looney, L. (2003). Simulation of the stir casting process. Journal of Materials Processing Technology, 144, 567-571. https://doi.org/10.1016/S0924 0136(03)00368-6
Ravi, K. R., Sreekumar, V. M., & Pillai, R. M. (2007). Optimization of mixing parameters through a water model for metal matrix composites synthesis. Materials and Design, 28, 871 881. https://doi.org/10.1016/j.matdes.2005.10.007
Lu, J., & Lu, Z. (2010). Optimization of stirring parameters through numerical simulation for the preparation of aluminum matrix composite by stir casting process. Journal of Manufacturing Science and Engineering, 132, 061007:1-7. https://doi.org/10.1115/1.4002851
Sahu, M. K., & Sahu, R. K. (2017). Optimization of stirring parameters using CFD simulations for HAMCs synthesis by stir casting process. Transactions of the Indian Institute of Metals, 70, 2563-2570. https://doi.org/10.1007/s12666-017-1119-5
Vijaya Ramnath, B., Elanchezhian, C., Jaivignesh, M., Rajesh, S., Parswajinan, C., & Siddique Ahmed Ghias, A. (2014). Evaluation of mechanical properties of aluminium alloy alumina–boron carbide metal matrix composites. Materials and Design, 58, 332-338. https://doi.org/10.1016/j.matdes.2014.01.068
Rahman, M. H., & Rashed, H. M. M. A. (2013). Characterization of Silicon Carbide Reinforced Aluminium Matrix Composite. In Proceedings of the 10th International Conference in Mechanical Engineering (pp. 103-109).
Bansal, S., & Saini, J. S. (2015). Mechanical and Wear Properties of SiC/Graphite Reinforced Al359 Alloy-based Metal Matrix Composite. Defence Science Journal, 65, 330 338.
Basaravaraju, S., Arasukumar, K., Bendigeri, C., & Umesh, C. K. (2012). Studies on Mechanical Properties and Tribological Characteristics of LM25-Graphite-Silicon Carbide and LM25-Flyash-Silicon Carbide-Hybrid MMC’s. International Journal of Innovation in Science, Engineering and Technology, 1, 107-112.
Shanmughasaundaram, P. (2015). Wear Behaviour of As-cast and Heat Treated Al7075 SiC composites. International Journal for Research in Applied Science & Engineering Technology, 10, 433-436.
Muthu, P., & Rajesh, S. (2016). Dry Sliding Wear Behaviour of Aluminium/SiC/Fly ash Hybrid Metal Matrix Composite. Journal of Australian Ceramic Society, 52, 125-130.
Sunil Kumar, K., & Srinivasamurthy, P. L. (2021). Tensile and hardness behavior of RRA treated aluminum 7075 alloy. Lecture Notes in Mechanical Engineering, 23, 563–575.
Sunil Kumar, K., & Srinivasa Murthy, P. L. (2019). Retrogression and re-aging of AL 7075 microstructure and corrosion behavior characterization. International Journal of Engineering and Advanced Technology, 9(1), 4377–4383.
Sunil Kumar, K., & Srinivasa Murthy, P. L. (2019). Effect of retrogression and re-aging on fatigue crack growth behavior of Al 7075 alloy. International Journal of Innovative Technology and Exploring Engineering, 8(10), 243–247.
Sunil Kumar, K., & Srinivasa Murthy, P. L. (2019). Study on tribological characterization of RRA treated aluminium 7075 alloy. Journal of Advanced Research in Dynamical and Control Systems, 11, 560–569.
Sunil Kumar, K. (2016). Development of standing wave thermo acoustic prime mover. International Journal of Research in Advent Technology, 4(4). E-ISSN: 2321-9637.
Sunil Kumar, K. (2016). Design and development of automated suspension to chassis damage. International Journal of Research in Advent Technology, 4(4). E-ISSN: 2561-9762.
Sunil Kumar, K. (2017). Effect of heat treatment on the corrosion behavior of high strength aluminium alloy. International Journal of Mechanical and Production Engineering, 5(10). ISSN: 2320-2092.
Sunil Kumar, K. (2017). A review on microstructure and corrosion behaviour of RRA treated 7075 Al alloy. International Journal of Scientific Research Engineering & Technology (IJSRET), 6(9). ISSN: 2278-0882.
Sunil Kumar, K. (n.d.). Design and analysis of a turning fixture for oil tank cover MGB. International Journal of Recent Trends in Engineering & Research. ISSN: 2455-1457.
Sunil Kumar, K. (2016). Pneumatic three axis modern trailer. International Journal for Research in Applied Science & Engineering Technology (IJRASET), 4(5). ISSN: 2321-9653.
Sunil Kumar, K. (2024). Design and development of pneumatic sheet metal cutting machine. International Journal of Scientific Research in Mechanical and Materials Engineering (IJSRMME), 8(3). https://doi.org/10.32628/IJSRMME2483
Sunil Kumar, K. (2023). A new dimension in 3D printing. International Journal of Advanced Research in Science, Communication and Technology, 3(2). ISSN: 2581-9429.
Sunil Kumar, K. (2023). Design and development of dual extruder 3D printing. International Journal of Advanced Research in Science, Communication and Technology, 3(2). ISSN: 2581-9429.
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Dr. Sunil Kumar K, Arun Kumar B R, K C Saqhib Pasha, Naveenkumar Y M, Nithish K (Author)
This work is licensed under a Creative Commons Attribution 4.0 International License.
