A Study of Surface Morphology and Wear Rate Prediction of Coated Inconel Specimen of 600, 625 and 718

Authors

  • Vinod Kumar  Research Scholar-Mechanical Engineering Department- Presidency University, Bengaluru, Karnataka, India
  • Dr. Udaya Ravi M  Professor-Mechanical Engineering Department-Presidency University, Bengaluru, Karnataka, India
  • Dr. Yuvaraja Naik  Assistant Professor-Mechanical Engineering Department-Presidency University, Bengaluru, Karnataka, India

Keywords:

Wear Rate, Pin, Disc, Load And Speed

Abstract

In the current work the coated Inconel specimens 600,618 and 625 are used to find the wear rate. and these three different grades Inconel specimen were tested for their wear rate calculation by using pin on disc wear machine by varying different loads and speeds and all these three different Inconel specimen wear rate values are calculated and are compared and it was found that among three different Inconel specimens 600, 625 and 718 the dominant type of specimen is Inconel 625 and is an important coating material property with regard to the wear rate behaviour under pin on disc test conditions. and it is observed that well known Inconel specimen 625 is much more promising coating material and done details study of surface morphology of Inconel coated specimen 600, 625 and 718.

References

  1. Y. Fukuda, H. Yamasaki, M. Kawahara, and H. Kimura, “Detonation coating for coal fired tubes,” Proceedings of International Symposium on Advanced Thermal Spray Technology and Applied Coating, Japan High Temperature Society, Osaka, 1988, pp49-54.
  2. K.J. Stein, B.S. Schorr, and A.R. Marder, “Erosion of thermal spray MCr-Cr3C2 cermet coatings,” Wear, Vol. 224, pp. 153-159, 1999.
  3. Cueva A., Sinatora W.L., Guesser A.P. and TschiptschinA., “Wear resistance of cast irons used in brake disc rotors”, Wear, Vol. 255, PP. 1256-1260,2003.
  4. DurgaV., RaoN., BoyerB.A., CikanekH.A. and Kabat D.M.,“Influence of surface characteristics and oil viscosity on friction behaviour of rubbing surfaces in reciprocating engines”. Fall Technical Conference
  5. Sidhu H.S., Sidhu B.S. and Prakash S.,“Solid particle erosion of HVOF sprayed NiCr and Stellite-6 coatings”, Surface and Coatings Technology,Vol.202, PP.232-238, 2007.
  6. Picas J.A., Forn A. and Matthaus G., “HVOF coatings as an Alternative to Hard Chrome for pistons and valves”,Wear,Vol. 261,PP.477-484,2006.
  7. U. Erning, M. Nestler, HVOF coatings for hard-chrome replacement-properties and applications, in: Proceedings of United Thermal Spray Conference (UTSC 99), Düsseldorf, Marzo 1999, pp. 462–466
  8. P.L. Ko, M.F. Robertson, Wear 252 (2002) 880–893.
  9. Bhushan, B.; Gupta, B.K. Handbook of Tribology: Materials, Coatings, and Surface Treatments; Krieger Pub Co.: Malabar, FL, USA, 1991
  10. C.-J. Li, Y.-Y. Wang, G.-J. Yang, A. Ohmori, and K.A. Khor, “Effect of solid carbide particle size on deposition behavior, microstructure and wear performance of HVOF cermet coatings,” Mater. Sci. Technol., Vol. 20, pp. 1087-1096, 2004.
  11. P. Vuoristo, K. Niemi, A. Makela, and T. Mantyla, “Abrasion and erosion of wear resistance of Cr3C2 -NiCr coatings prepared by plasma, detonation and high velocity oxy-fuel spraying,” Thermal Spray Industrial Applications, C.C. Berndt and S. Sampath, Eds., Materials Park, OH, USA: ASM International, 1994, pp. 121-126
  12. C.-J. Li, G.-C. Ji, Y.-Y. Wang, and K. Sonoya, “The dominant mechanism of carbon loss during HVOF spraying of Cr3C2 -NiCr,” Thin Solid Films, Vol. 419, pp. 137-143, 2002.,
  13. C.-J. Li, K. Sonoya, G.-C. Ji, and Y.-Y. Wang, “Effect of spray conditions on the properties of HVOF Cr3C2 -NiCr coatings,” Weld. World, Vol. 41, pp. 77-87, 1998.
  14. J.M. Guilemany, N. Espallargas, P.H. Suegama, A.V. Benedetti, and J. Ferna ´ndez, “High-velocity oxy-fuel Cr3C2 -NiCr replacing hard chromium coatings,” J. Thermal Spray Technol., Vol. 14, pp. 335-341, 2005.
  15. M. Roy, A. Pauschitz, J. Bernardi, T. Koch, and F. Franek, “Microstructure and mechanical properties of HVOF sprayed nanocrystalline Cr3C2 -NiCr (Ni20Cr) coating,” J. Thermal Spray Technol., Vol. 15, pp. 372-381, 2006.
  16. T.S. Sidhu, S. Prakash, and R.D. Agrawal, “Characterizations and hot corrosion resistance of Cr3C2 -NiCr coating on Ni-base superalloys in an aggressive environment,” J. Thermal Spray Technol., Vol. 15, pp.811- 816, 2006.
  17. C.-J. Li, H. Yang, and H. Li, “Effect of gaseous conditions on the characteristics of HVOF Flame and structure and property of WC-Co coatings,” Mater. Manuf. Process., Vol. 14, pp. 383-395, 1999.

IInternational Journal of Scientific Research in Mechanical and Materials Engineering

Downloads

Published

2023-06-30

Issue

Volume 7, Issue 3, May-June-2023

Section

Research Articles

License

Copyright (c) IJSRMME

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

[1]
Vinod Kumar, Dr. Udaya Ravi M, Dr. Yuvaraja Naik, " A Study of Surface Morphology and Wear Rate Prediction of Coated Inconel Specimen of 600, 625 and 718, IInternational Journal of Scientific Research in Mechanical and Materials Engineering(IJSRMME), ISSN : 2456-3307, Volume 7, Issue 3, pp.15-23, May-June-2023.