Mineral Filler Effect on Tensile Parameters of Randomly Oriented and Woven Fabric Plastic Laminates

Authors

  • Lokesh KS   Assistant Professor, Department of Mechanical Engineering & Faculty of Nano Technology, Srinivas Institute of Technology, Karnataka, India

Keywords:

Mineral Fillers, Axial Loading, Lightweight Materials

Abstract

Use of mineral fillers draws researchers attention to retain the commercial qualities of fibre reinforced light weight structures. This work signifies the use of two types of E-glass fibres namely woven fabric and randomly oriented fibres are used as a reinforcing materials and epoxy resin constitutes matrix system. Several studies proved that the strength of GFRP composites progressively increased with adding fillers. Keeping this in mind the present work highlights the utilization of mineral filler called calcium ino silicate powder having the composition of CaSio3 as a filler material. By employing hand layup technique samples have been prepared from both woven and chopped type and tensile test is conducted as per ASTM standards and corresponding results are tabulated and recorded. The present work also highlights the comparison of tensile strength for both woven and chopped laminates. It is observed that use of mineral filler influences greatly on tensile properties of polymer matrix composite and it is also cleared that woven laminates shows greater resistance to tensile loading as compared to randomly oriented fibre.

References

  1. Dr.P.K.Palani,M.NandaKumar,"Analysis of Mechanical Properties of chopped strand Mat S-Glass epoxy resin NanoclayComposites",The International Journal of Engineering and Science (Ijes)||Volume||2||Issue||2||Pages||185189||2013||Issn:2319-1813 ISBN:2319-1805.
  2. KS Lokesh , Evaluation of Toughness on Varied Thickness of Chopped Strand Mat /PU-foam Sandwich Structures , International Research Journal of Engineering and Technology(IRJET), e-ISSN:2395-0056 Volume: 05 Issue: 09 | September-2018, p-ISSN: 2395-0072
  3. KS Lokesh , Synthesis and Study on Effect of Thickness on 3-point Bending Strength of Sandwich Composites, International Research Journal of Engineering and Technology(IRJET), e-ISSN:2395-0056 Volume: 05 Issue: 08 | August-2018, p-ISSN: 2395-0072
  4. KS Lokesh , Preparation and Tensile strength Evaluation of Synthetic fibers Sandwiched with Foam structures. International Research Journal of Engineering and Technology(IRJET), e-ISSN:2395-0056 Volume: 05 Issue: 09 | September-2018, p-ISSN: 2395-0072
  5. Harris B,"Fatigue and Accumulation of damage in Reinforced Plastics", Composites, 8,1977, 214-220.
  6. KS Lokesh, T Pinto ,Experimental Study on Effect of Metallic Oxides Mixture on Tribological Behaviour of Aluminium Based Metal Matrix Composites, International Research Journal of Engineering and Technology(IRJET),e-ISSN:2395-0056 Volume: 05 Issue: 06 | June-2018, p-ISSN: 2395-007
  7. Konur O and Mathews F.L," Effects of the properties of the constituents on the fatigue Performance of Composites: A Review", Composites, 20(4), 1989, pp.317-328.
  8. Lokesh K.S, Dr.Thomas Pinto, & Ravi S.M. (2017). Evaluation of Mechanical Properties and Wear Characterization of Polymer Composites under Varying Temperature Conditions: A Review. International Journal of Engineering and Information Systems(IJEAIS),1(4),64–68. http://doi.org/10.5281/zenodo.821168
  9. Lokesh K. S., Bandu Ummaji, Gururaj P., K. Rayappa, Yashavantha J., Effect of Red Mud Particles on Scratch Resistance of Aluminum Based Metal Matrix Composites, American Journal of Aerospace Engineering. Vol. 5, No. 1, 2018,pp. 24-29. doi: 10.11648/j.ajae.20180501.14
  10. Lokesh KS, "Impact of Modified Thickness on Flexural Modulus of PU-Foam /CSM Glass Fabric Sandwich Panels ",International Journal of Scientific Research in Mechanical and Materials Engineering (IJSRMME), ISSN : 2457-0435, Volume 2 Issue 3, pp. 29-35, July-August 2018.URL :http://ijsrmme.com/IJSRMME182210
  11. Lokesh K S , Karthik B.Y, Avinash C.G, Ganesh Kamath, Samson Lobo, "Experimental Study on Tribological Characteristics of E-waste filled Fibre Reinforced Plastics ", International Journal of Scientific Research in Mechanical and Materials Engineering (IJSRMME), ISSN : 2457-0435, Volume 2, Issue 1, pp.11-16, .2018URL http://ijsrmme.com/IJSRMME182203
  12. Lokesh K S, Dr.Thomas Pinto, Mohammed Gowspeer, Effect of E-waste Rubber on Wear Behaviour of Glass fibre Reinforced with Epoxy Composites Pages: 20-25 DOI: 10.7324/IJASRE.2018.32624 DOI URL: http://dx.doi.org/10.7324/IJASRE.2018.32624
  13. Lokesh KS, "Study on Processing and Axial loading Conditions of Lightweight Materials ",International Journal of Scientific Research in Mechanical and Materials Engineering (IJSRMME), ISSN : 2457-0435, Volume 2 Issue 4, pp. 21-27, September-October 2018.URL : http://ijsrmme.com/IJSRMME18347
  14. KS Lokesh, T Pinto , Comparative Study on Axial Loading Conditions and Effect of Mineral Filler on CSM and WF Fibres , International Research Journal of Engineering and Technology(IRJET),e-ISSN:2395-0056 Volume: 05 Issue: 10 | October-2018, p-ISSN: 2395-0072
  15. Lokesh KS, Dr. Thomas Pinto, "Experimental Study on Tensile Effect of Different E-glass Fabric Laminates Reinforced with Potential Adhesives ",International Journal of Scientific Research in Mechanical and Materials Engineering (IJSRMME), ISSN : 2457-0435, Volume 2 Issue 5, pp. 14-22, November-December 2018.
    URL : http://ijsrmme.com/IJSRMME18253
  16. Lokesh KS, "Evaluation of Flexural Rigidity of PU - foam Cored Sandwich Structures",International Journal of Scientific Research in Mechanical and Materials Engineering (IJSRMME), ISSN : 2457-0435, Volume 2 Issue 5, pp. 36-42, November-December 2018.
    URL : http://ijsrmme.com/IJSRMME18255
  17. Lokesh K S , "Abrasive Study of ELT Rubber Loaded with Fibre Reinforced Plastics",International Journal of Scientific Research in Mechanical and Materials Engineering (IJSRMME), ISSN : 2457-0435, Volume 2 Issue 5, pp. 43-48, November-December 2018.
    URL : http://ijsrmme.com/IJSRMME18256
  18. Lokesh KS, Dr.Thomas Pinto, "Review on Tribological Parameters of Fibre Reinforced Plastics Modified with Mineral Fillers ",International Journal of Scientific Research in Mechanical and Materials Engineering (IJSRMME), ISSN : 2457-0435, Volume 2 Issue 5, pp. 49-56, November-December-2018.
    URL : http://ijsrmme.com/IJSRMME18257

IInternational Journal of Scientific Research in Mechanical and Materials Engineering

Downloads

Published

2018-10-30

Issue

Volume 2, Issue 4, September-October-2018

Section

Research Articles

License

Copyright (c) IJSRMME

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

[1]
Lokesh KS , " Mineral Filler Effect on Tensile Parameters of Randomly Oriented and Woven Fabric Plastic Laminates , IInternational Journal of Scientific Research in Mechanical and Materials Engineering(IJSRMME), ISSN : 2456-3307, Volume 2, Issue 4, pp.28-33, September-October-2018.